浙江双威数控电子机械有限公司
首页 | 联系方式 | 加入收藏 | 设为首页

产品目录

联系方式

联系人:李先生
电话:0571-8711968
邮箱:service@battytech.com

站内搜索

当前位置:首页 >> 新闻中心 >> 正文

变压器绕线机缠绕技巧

编辑:浙江双威数控电子机械有限公司   时间:2014/03/31   字号:
摘要:变压器绕线机缠绕技巧

 变压器绕线机的绕线技巧是非常重要的,首先必须对被绕物之线材种类特性,圈数之多少以及外观材质,缠绕速度要有如自粘线,漆包棉线等,所设定之线径要增大很多,因外皮不太光滑,较无惯性特点。细线缠绕速度不要太慢,但必须用慢速爬升启动,以免将线材拉断。粗线则速度不宜过快(超速),但必须注意中低速扭力是否足够。

Transformer winding machine winding technique is very important, first of all have to be around the wire which features, the number of how many circles and material appearance, like the glue line winding speed, enamelled cotton thread, etc., the line set by the diameter to increase a lot, because of the skin is not very smooth, less inertia characteristics. Filament winding speed not too slow, but must be started with a slow climb, so as to avoid the wire broken. Thick line shoulds not be too fast speed (speed), but must pay attention to the low speed torque is enough.

变压器绕线机使用铝线时请注意,涨力要调至比同等粗细的铜线小很多,以免线径拉细,外绝缘漆爆裂,影响产品质量。使用铝线时因涨力减小,所设定之线径要适当增大。结合自己的涨力需要可以少走一些过线轮。变压器绕线机被绕物的型状与排线器之高低和出线距离有相当大的关系方型被绕物速度不要太快,中间会有圆凸不平整,影响排线整齐。

Note that when using aluminium wire tension to switch to smaller than copper wire of the same thickness, in order to avoid yarn diameter, fine, insulating paint outside blowout, affect the quality of the product. When using the aluminium wire for tension decreases, and the line set by the diameter to increase appropriately. To meet the needs of their tension can go less line wheels. Transformer winding machine is the shape of round objects and discharge line have a considerable height and the outlet of the distance square was winding speed not too fast, there will be a circular convex uneven among affected row of neat line.

变压器绕线机被绕物与排线器之高度要适当,太低线容易陷入下面一层,太高则会有跳线现象。排线器与被绕物之出线距离不宜太远,会影响排线随耦之精确度。排线器之出线松紧,亦关系着绕线及排线漂亮与否。绕线机设置注意事项校准被绕物之宽度及启绕点为第一优先,且最为重要。当启绕点正确无误,开始绕线,可用两端停车先行测试所设之宽度是否正确。

Be around and wiring of highly appropriate, one layer below the low line easily, high jump line may break phenomenon. Ribbon cable and be around shoulds not be too far away, the qualification of distance will affect the ribbon cable with the precision of the coupling. Wire on the ribbon cable slack, also relationship between the winding and line is beautiful or not. Winding machine set considerations for calibration was around the material width and rev about point as the first priority, and the most important. When the rev about point is correct, start winding, parking available on both ends of the test first set the width is correct.

 

上一条:绕线机主轴动力机构的维护要点 下一条:变压器绕线机出现故障解决方法